3-pin Input Connector.
Process input (Volts / Current) plus 24 V Excitation.
Excitation Header.
External 24 V available
Signal Type Header.
Voltage / Current
Input Range Header.
Selects 2 V, 5 V, 10 V, 20 V, 200 V,
2 mA, 20 mA, Custom
Interface to
Tiger Meter.
Introducing IP07 The mainstay in process interfacing.
IP07 is a versatile input module presented as a general purpose interface to a wide range of DC voltage or milliamp signal inputs. With an external excitation voltage available to power transducers and onboard selectable headers for interface options, IP07 is the ideal choice between the process inputs and board selectable headers for interface options, IP07 is the ideal choice between the process inputs and your Texmate controller.
p g p g
g g
p p
p p
Input Module
Order Code Suffix
IP07
Signal Type
Choice of DC volts or DC current (header selectable).
Voltage Ranges
Current Ranges
2 V, 5 V, 10 V, 20 V, and 200 V DC (header selectable). (Input Impedance approximately 1 megohm)
2 mA, 20 mA, 1Custom (header selectable). (200 mV drop across shunt resistor)
External Excitation
+24 V DC (150 mA maximum).
Interface
Accuracy
Tiger 320 Series and Leopard range.
0.05% of reading.
Temperature Drift
Typically 50 ppm/C.
Fits Leopard
& Tiger 320 Series
See
Popular IP07 Connection
Configurations
For connection details
Figure 1 IP07 Component Layout
Figure 2 is an IP07 signal flow diagram showing the input signal flow through the signal type, voltage range, and current range headers to the Tiger or Leopard controller for further processing. The signal type header channels the input signal to either the voltage or current range header, which is set to suit the input voltage or current.
For Tiger or Leopard controller supplied +24 V DC excitation, set the excitation header to ON.
If excitation is supplied externally (e.g. from the transducer) set the excitation header to OFF.
Figure 2 IP07 Signal Flow Diagram
Table 1 provides a list of process input signals with and without external excitation and shows the appropriate header positions for each signal type. See diagrams on Page 3.
TABLE 1
POPULAR IP07 CONNECTION CONFIGURATIONS & HEADER POSITIONS
Input
Header Positions
Excitation
Signal Type
Input Range
External Excitation
0-10 V Process Input
0/4-20 mA Process Input
OFF
OFF
VOLTAGE
CURRENT
Controller Supplied Excitation +24 V (150 mA)
Loop Powered Sensors (Current Mode)
0-10 V Process Input
0/4-20 mA Process Input
CURRENT
VOLTAGE
CURRENT
10 V
20 mA
20 mA
10 V
20 mA
External Excitation
0 to 10 V Process Input.
+POS
N/C
+24 V Exc
NEG
+ Supply
+ Signal
External
Supply
Supply
Signal
4 to 20 mA Process Input.
+ Supply
External
Supply
Supply
+ Signal
+POS
+24 V Exc
N/C
NEG
Signal
Controller Supplied Excitation +24 V (150 mA)
2-wire, Loop Powered Sensors (Current Mode).
+POS
+24 V Exc
NEG
N/C
Sensor
3-wire, 0 to 10 V Process Input.
+ Signal
+ Supply
+POS
+24 V Exc
NEG
Signal / Supply
3-wire, 4 to 20 mA Process Input.
+ Signal
+ Supply
+POS
+24 V Exc
NEG
Signal / Supply
Calibration
Enter the Calibration Mode and set the [ZEro] and then the [SPAn] settings, while applying a low and then a high signal.
For a full set of calibration and decimal point placement procedures, see your relevant Leopard controller user manual.
Calibration and Input Signal Type Selection Enter the Calibration Mode and then Code 2 to set the following calibration and input signal type settings for CH1:
CAL
000
for CH1 select
111
CODE_2
000
60 Hz Operation:
CODE_2
100
50 Hz Operation:
Code 2 frequency selection applies to all channels
Note, to calibrate the input signal for other engineering units use CH2, CH3, or CH4. These can be viewed
by pressing the
button while in the operational display.
for CH2 select
112
CODE_4
for CH3 select
113
CODE_5
for CH4 select
114
CODE_6
010
010
010
For a full set of calibration and decimal point placement procedures, see your relevant Tiger meter controller manual.
Tel: 1-760-598-9899 USA 1-800-839-6283 Thats 1-800-TEXMATE
Volts
Amps
Display
Input Low
Input High
For product details visit www.texmate.com
Page 4
Texmate, Inc. Tel. (760) 598-9899 www.texmate.com
IP07 (NZ342)
Texmate is an American manufacturer of high durability industrial grade panel meters, bar graphs, and transducers. Texmate's meters are frequently equipped with relays and various signal outputs for industrial automation applications and are known for their extremely long service life.